36v ezgo will not move and solenoid is not clicking

Mar 2, 2023. #1. I'm new to the forums and I'd like to thank you for any help in advance. We have a 2009 EZGO RXV with no reverse buzzer. Solenoid clicks, E brake disengages, but will not move in forward or reverse. When we put cart in tow position we can move it. Checked all switches and bypassed diagnostic plug.Adjusting a faulty solenoid might take you a simple replacement. Signs of a faulty solenoid can be detected by putting your cart forward and pressing down the accelerator. You may hear clicks. Place a multimeter on the larger terminal of the solenoid and check for readings. If it reads more than 0.4 ohms, your solenoid may require a replacement.May 14, 2010. #4. If your not getting a soleniod click jack the rear end up and take that cover off over the solenoid get a peice of 6 gauge cable and jump the large post of solenoid. Turn key on press pedal if cart runs replace solenoid, There is a diode and a resistor mounted on top of solenoid so be careful with them and make sure you put ...Oct 4, 2022 ... ... solenoid from your company so I could convert it from 36v to 48v ... I get a click, but it doesn't ... not moving issue - 2016 EZGO RXV clicks but ...Switch the cart key to the off position, and make sure the cart is set to neutral. Ensure your voltmeter is set to ohms, and place a probe on both large terminals. There should be no reading. Set the cart to the forward position, and turn the key to the on position. Go ahead and step on the accelerator.Yamaha 36 Volt will not go. I have an older 36 volt gc. Brand new batteries, new solenoid, but will not run. I checked the in line fuse on drivers side, behind the seat, good. I checked main key switch, good, I checked the switch under gas pedal, good, Reed switch at charger plug, good, all connections and cables are good.Nov 6, 2018 · When I turn the key to "on" there is no click from the solenoid. Have checked voltage into the big bolts on it and it is at 48Volts. Tried checking small bolts for voltage but not getting anything there. I don't think any power is getting to them when I have the cart in "run", key switch "on", F/R switch in "F" and the pedal depressed.May 14, 2010. #4. If your not getting a soleniod click jack the rear end up and take that cover off over the solenoid get a peice of 6 gauge cable and jump the large post of solenoid. Turn key on press pedal if cart runs replace solenoid, There is a diode and a resistor mounted on top of solenoid so be careful with them and make sure you put ...I have no click to the solenoid unless I supply B- to the blue terminal of the solenoid. Reed is already bypassed, have pack voltage at pedal switch input and output. Have power at key switch, I have power at FNR switch in both directions. Reverse buzzer work. Even with B- supplied to the blue terminal the cart will still not move.99 EZGO TXT 36v Series cart. Cart just stopped. Now clicks in solenoid and doesn't move. Has all new parts on. Alltrax SR48600, SW200 solenoid, micro switches for F/R, micro for pedal, IT sensor and had the motor cleaned. Batteries are 1yr old with 2AWG cables for batteries and motor. Not sure if i rewired something wrong or what.Re: Txt 36v nativas controller, solenoid clicks but does not move. Since the controller does not supply amps to the solenoid in a series drive, I suspect the controller is still configured for a Sepex drive.The solenoid would click and the controller was getting power, turn out the wire was the issue. I have a 1995 electric ezgo cart and one day it stopped working. The solenoid would click and the ...Re: Electrical issue. I get 36 volts to both small terminals on solenoid when gas ped. If your getting the solenoid to "click" the small terminals are OK. One of them provides battery voltage (36+) the other provides (-) to complete the circuit and throw the switch. Have you checked to see if you have continuity between the large posts when the ...When pedal pushed only far enough for solenoid to click, you should get full battery pack voltage and the voltage should decrease to nearly zero as pedal is pushed to floor.If you don't get full pack voltage (should be 38.2V for a fully charged pack) when solenoid first clicks, start tracing circuit back towards solenoid contacts.Aug 23, 2020. #1. 2007 EZGO PDS 36V cart (34-volt Referenced): When the cart is on the ground no forward movement at all, Reverse attempts to move but gives up: When I lifted the cart and pressed the pedal (slightly) the wheels will move (Forward and Reverse) but if I push the pedal a little farther the solenoid kicks out (wheel movement stops ...Not Yet Wild. Join Date: Aug 2019. Posts: 12. Re: 36v ez go with pds won’t move in forward or reverse. Fully charged pack voltage is about ~37.4. Voltage doesn’t change at all with pedal, and the solenoid doesn’t click with the pedal. Solenoid is closed in forward Solenoid is open in neutral Solenoid is closed in reverse.On an electric golf cart, if the solenoid is silent – no clicking – use the setting voltmeter to DC volts using the 200 range. First, turn on the ignition while looking for a reading on the smaller terminals. If nothing is appearing, then press on the accelerator. If the needle doesn’t move, then the problem is not with the solenoid.Thanks in advance for your help. Jonathan. A 2012 1206HB-5201 controller PWMs the voltage to a 36V solenoid. 36V is the pull-in voltage for about half a second, then it reduces to a 28V hold-in voltage. You should never take solenoid - to battery pack - because the solenoid coil would overheat from direct 48V and be damaged.Join Date: Oct 2023. Location: North Alabama. Posts: 1. Newly Purchased 2000 48V Club Cart DS Solenoid Clicks, but not running. I'm new here, first post. I just purchased a 2000 48V DS Series Cart. Unfortunately, I was in a hurry to buy and didn't do a lot of research before hand. I typically spend weeks before a purchase like this, but I was ...Examining the Solenoid. If your EZGO golf cart starts to move and then stops abruptly, a malfunctioning solenoid could be the issue. The solenoid is responsible for allowing power to flow from the battery to the motor, so it's essential to ensure it's working correctly. Here are some troubleshooting tips to examine the solenoid:It’s highly recommended when you replace the controller, you replace the solenoid and vice versa. 6. Clean The Air Filter. Air Filter. The EZGO golf cart won’t move after starting if the air filter of the EZGO golf cart somehow got clogged with debris or some other thing.Thanks much I will leave it on for a while more …the last full charge was up to 38.2…also the batteries hold a charge just fine, lipo gone back to lead acid and we shall see… but i do have a 3 inch body lift and 23x10.5x12 tires…looks like it is all stock…controller and motor so if it ran fine before should still be fine and will ...HOW TO TROUBLESHOOT A EZGO TXT 48V. THESE ARE THE COMMON PROBLEMS. THAT WE SEE AT OUR SHOP... ALWAYS REMEMBER SAFETY FIRST. ALWAYS JACK CART UP FROM THE ...Sep 1, 2012 · Posts: 2,408. Re: EZ GO Electric Cart Clicks but NO movement Forward or Reverse!! Just because the solenoid clicks, does not mean it's working! When your cart won't run, try jumping the two large terminals on the solenoid and see if it will run then. If it does, replace your solenoid. Mine had intermittent running once.2011 EZGO RXV Freedom. I turn the key from off position to neutral I hear the solenoid click when I move to reverse I hear the reverse alarm but won't move, when I select forward the cart will not move either. what are the probable causes? jeveler New Member. Jan 8, 2022 #2Options. Sounds like the motor is not getting all the voltage it needs to move. Check your connections at the solenoid and the motor. If you are not getting enough voltage at the solenoid, check for bad fuses or circuit breakers. If voltage is good at the solenoid, but not the motor; suspect the solenoid is going bad.Got 36v ezgo pds. Suddenly stopped and solonoid resistor getting real hot. I changed the solonoid and - Answered by a verified Electric Vehicle Mechanic ... No click of solonoid. Charger working well. Got 38 v at battery pack. ... ez go cart will not move, if I keep pressing the foot petal 1 out of 25 times it will move a inch or so ...2001 36v EZGO - good voltage, key switch continuity, no reverse beep, solenoid not activating, no movement. ... 2002 EzGo Text won't move. Newer batteries. Solonoid clicks when depressing the pedal. But no movement It was running a couple of weeks ago, but kept dying ... No clicking at solenoid o ...Re: ezgo PDS solenoid wont click. Both B+ (Yellow wire) and B- (Blue wire) are supplied to the solenoid coil by the controller. To get B+ to the yellow wire: Charger disconnected from cart, Run/Tow = Run, Keyswitch = ON, F/R = either F or R. To get B- to the blue wire: All the above conditions must be met, plus pedal must be depressed far ...#1. Hey I've got a 36 volt EZGO TXT in forward or reverse it clicks and wont move. I installed new solenoid at control board same issue no go any ideas appreciated thanks. HotRodCarts. Cartaholic. Feb 14, 2022. #2. What year is your EZGO? Is it DCS, PDS or series? Check your battery pack voltage and post the results. Hillbillyman1985. New Member.Options. Sounds like the motor is not getting all the voltage it needs to move. Check your connections at the solenoid and the motor. If you are not getting enough voltage at the solenoid, check for bad fuses or circuit breakers. If voltage is good at the solenoid, but not the motor; suspect the solenoid is going bad.When I turn the key to "on" there is no click from the solenoid. Have checked voltage into the big bolts on it and it is at 48Volts. Tried checking small bolts for voltage but not getting anything there. I don't think any power is getting to them when I have the cart in "run", key switch "on", F/R switch in "F" and the pedal depressed.Aug 7, 2018. #12. To jump the solenoid you run a jumper (6 gauge or larger) from one large solenoid post to the other large solenoid post. Make sure the run tow switch is in the tow position when you do this. The EZGO DCS controllers are fragile and I've seen them fry when jumping the solenoid. J.If you have ~15v I think that should still be good. Measure between the controller 5 pin white wire and B-, push the pedal down and see what the voltage reads. Should start somewhere around 0.5v when the solenoid clicks then go to ~2v at full pedal. If no voltage check at the ITS terminals themselves.An EZGO RXV golf cart won't charge because of a dead battery, low battery pack voltage, a non-charging charger or a faulty battery cable. Measure the positive and negative voltages of the battery pack using a multimeter. Depending on the charge level, it should read between 46 to 50 volts for a 48-volt cart.Re: ezgo PDS solenoid wont click. Both B+ (Yellow wire) and B- (Blue wire) are supplied to the solenoid coil by the controller. To get B+ to the yellow wire: Charger disconnected from cart, Run/Tow = Run, Keyswitch = ON, F/R = either F or R. To get B- to the blue wire: All the above conditions must be met, plus pedal must be depressed far ...Step 2: Testing the Solenoid Coil. Using a multimeter, set it to the ohm range and place one meter lead to the small terminal on the solenoid and the other to the solenoid's metal case. If the meter reads no resistance, the solenoid coil is faulty and needs to be replaced.Posts: 15. Melex golf cart 36v solenoid not clicking dont believe I have voltage I need. I have a melex 36 volt cart with brand new batteries and a brand new solenoid. I get power to solenoid and key switch is functioning properly but when I step on gas pedal I don't get voltage to the 2 big lugs on solenoid. Solenoid doesn't click or anything.We would like to show you a description here but the site won't allow us.after solenoid has closed • Confirm the solenoid is working properly. Change solenoid if required. • Put vehicle in Neutral. Measure voltage on main terminals (high current connections) of the solenoid. Depress throttle and listen for solenoid to click. If solenoid clicks and the voltage does not drop to zero between the main terminals.Evening, I am new here. Have been tinkering on carts for a couple of years. Recently acquired a 36v EZGO DCS cart. The cart has new batteries. Solenoid clicks but won't move. Solenoid clicks with the key. From my understanding it should click when the pedal. Solenoid has same voltage (37.1) on either both inside and outside posts.Locate the solenoid and remove it from the golf cart. Step 3. Clean the solenoid terminals with a Wire brush. Step 4. Use a digital multimeter to test the solenoid's resistance. Step 5. Check for continuity between the solenoid's terminals. Step 6. Test the solenoid's voltage with a digital multimeter.Electric Vehicle Mechanic: Curtis B. solenoid has to work the same in reverse as in forward, if it doesn't you get no reverse. The only thing that affects both forward and reverse, is the forward and reverse switch. You can swap the two cables on the F/R switch, the ones on the 3 o'clock and 9 o'clock position, to ee if the problem changes.2016 EZGO RXV will not move, fully charged and solenoid checks good. 5 days. I would like to try. That's the only issue - Answered by a verified Technician By chatting and providing personal info, you understand and agree to our ...If your batteries are fully charged and your vehicle won't run, when you press on the accelerator pedal, then you should hear a clicking sound which will ...

Not hearing a 'clicking' sound; Since a solenoid helps to start your cart, it becomes impossible to move your cart if the solenoid has any problem. You will not hear a whirring "clicking" sound while starting the cart if the solenoid is damaged. Not getting enough speed; It is known that a solenoid's duty is to transmit current to the ...Cartaholic. Oct 29, 2014. #13. Look at the reed switch wire on back of charge receptacle. It is the small white wire and unplug connector, on the receptacle side of plug there should be 36 volts with the charger disconnected. If not switch is bad and no power is coming out to key switch.Here are the steps to bypass the solenoid on a golf cart: 1. Begin by disconnecting the negative battery cable from the battery to ensure there is no power flowing through the system. 2. Locate the starter solenoid on the golf cart. It is usually mounted near the battery or the starter motor. 3.96 EZGO Medalist 36v - Series Neighbor was borrowing cart gathering firewood, stated that it broke down and he had it pulled home. Now major issues. Issue #1 - I cant get solenoid to click w/o jumping across small + terminal to large battery terminal. One this is completed and I press pedal cart will run.

Solenoid valves use electromagnets to move a plunger attached to the valve to open or close it. Cutting the power to the electromagnet allows a spring or other force to return the ...May 29, 2020. #1. I have an EZGO with 36 volt system that won't run even though the batteries are fully charged. I have verified it is fully charged. Following some other troubleshooting online tips and measure the voltage on the controller when pressing on the pedal to go forward. Tip indicated voltage should go up as you press on pedal.Aug 23, 2020. #1. 2007 EZGO PDS 36V cart (34-volt Referenced): When the cart is on the ground no forward movement at all, Reverse attempts to move but gives up: When I lifted the cart and pressed the pedal (slightly) the wheels will move (Forward and Reverse) but if I push the pedal a little farther the solenoid kicks out (wheel movement stops ...Oct 29, 2023 · Testing The Solenoid. If your 36V Ezgo will not move and the solenoid is not clicking, it may be time to test the solenoid. By carefully examining this component, you can determine whether it is the cause of the problem and take appropriate action to fix it. Don’t hesitate to seek professional assistance if needed.Golf Cart Making Buzzing Noise. If your cart makes some buzzing noise, then do not worry. Chances are, it could be a minor issue and can be solved quickly.Feb 1, 2023 ... Comments6 ; EZGO TXT electric golf cart wont move. How to diagnose and troubleshoot. Golf Cart Whisperer!!!!!! · 13K views ; Solenoid Demonstration ...If your club car makes a clicking sound but doesn't move, the issue could be due to a faulty battery or damage to the internal controller. Check whether the batteries are working fine. Use a voltmeter to check the static voltage of the batteries. The readings should be around 50V. If the voltage turns out to be lower, then it's time to get ...Place the (+) probe to the controller side of the solenoid's large post. The reading should be 0.1 to 3 volts less than battery voltage. If the reading is more than 3 volts less the battery voltage, the resistor is faulty. If the voltage is the same as the battery voltage, replace the solenoid. 07-26-2017, 11:45 AM.Re: ezgo PDS solenoid wont click. Both B+ (Yellow wire) and B- (Blue wire) are supplied to the solenoid coil by the controller. To get B+ to the yellow wire: Charger disconnected from cart, Run/Tow = Run, Keyswitch = ON, F/R = either F or R. To get B- to the blue wire: All the above conditions must be met, plus pedal must be depressed far ...Solenoid Problems: The solenoid is responsible for connecting the battery to the motor, allowing the cart to move. If the solenoid is faulty or not clicking, it can prevent the cart …Re: Cart wont move, solenoid not clicking. Sounds like the activation circuit has issues. Or someone flipped it to Tow.. One common problem is the safety reed switch failing in the charger socket. First, flip the Run/Tow switch to Tow. There is a small red wire that comes off the back of the charger socket.I have a 2014 48volt EZGO RXV No electrical mods just a lift kit, tires and rims, custom paint etc. The cart is charged and has been working fine. today I went out, turned it on and it won't move. tried reverse and nothing however the alarm comes on. Lifted the seat and placed the toggle switch to roll. Nothing its locked up tight.Aug 31, 2015. #5. If by under the box you mean the controller/solenoid cover either the solenoid or controller are getting hot. Ride it a few minutes with the cover off and feel both. If the solenoid is hot I'd replace it with a with a White Rodgers 586. The stock solenoid will definitely get hot and eventually fail with bigger tires.2. Dirt Accumulation Throughout the Battery Ports. One of the most common and easy to fix reasons your golf cart may not move when you hear a click is dirt throughout the battery ports. This issue is common among Club Car carts because of the construction of their battery, which is fairly open compared to others.